Splashback, Solid Surface, Satin Grey, Apollo® Slab Tech

Filter

Complete your selection

Help

Help

Requested amount is in stock.
Limited stock available.
Item no longer available

Note:
To receive items as fast as possible, choose 'when available' at checkout.

Splashback, Solid Surface, Satin Grey, Apollo® Slab Tech

Image may show a similar article, please check product details.

Product details

Apollo® Slab Tech offers the warm seamless look of standard solid surface with the added appearance of natural stone
Inconspicuous, unobtrusive and seamless joints
Simple to install with a revolutionary new glue that allows the installer to remove the excess from any joints before it sets
20 mm and 30 mm solid mineral material
10 year limited manufacturer's warranty
Finished performance tested by FIRA®
Polished square edge
Easy to repair clean and maintain

Thickness

20 mm

Colour/finish

Satin grey

Splashback version

Splashback

Material

Mineral

Tolerance

Measuring up:
Apollo® Slab Tech solid surface can expand as much as 1 mm/mtr. Always allow a gap of at least 3 mm if for example, worktops are captive between walls
Tolerance is ±2 mm
Splashbacks and upstands over 100 mm high must have a minimum gap from the face to the rear of the hob - electric 50 mm, gas 100 mm
Allow a minimum 50 mm from the cut-out to the front edge
Wherever possible, joints in worktops should fall on a carcase end panel, giving added support to a joint
Joints should be a minimum of 100 mm from the sink or 120 mm from a hob cut-out
Allow a minimum of 120 mm between heated cut-outs
Stainless steel sink cut-outs to manufacturer’s recommendations
Overhangs in excess of 300 mm should be supported and the worktop should be supported every 600 mm
Installation:
Some colours have different levels of pigmentation (particles). This may lead to a variation in the aesthetic appearance of the worktop
Plastering or tiling should be completed after installation
Regular use of the car and maintenance kit should ensure worktops stay in good condition
Installation is relatively easy, for either a competent DIY enthusiast or recognised kitchen installer to carry out
No specialist tool required. Can be cut using normal woodworking routers and blades
Plan the worktop layout to ensure jonits don’t fall or within 100 mm of cut-outs

Order reference

Order jointing glue and worktop installation and care set separately

Warranty/guarantee information

Manufacturer warranty

Additional information attributes

Measuring up:
Apollo® Slab Tech solid surface can expand as much as 1 mm/mtr. Always allow a gap of at least 3 mm if for example, worktops are captive between walls
Tolerance is ±2 mm
Splashbacks and upstands over 100 mm high must have a minimum gap from the face to the rear of the hob - electric 50 mm, gas 100 mm
Allow a minimum 50 mm from the cut-out to the front edge
Wherever possible, joints in worktops should fall on a carcase end panel, giving added support to a joint
Joints should be a minimum of 100 mm from the sink or 120 mm from a hob cut-out
Allow a minimum of 120 mm between heated cut-outs
Stainless steel sink cut-outs to manufacturer’s recommendations
Overhangs in excess of 300 mm should be supported and the worktop should be supported every 600 mm
Installation:
Some colours have different levels of pigmentation (particles). This may lead to a variation in the aesthetic appearance of the worktop
Plastering or tiling should be completed after installation
Regular use of the car and maintenance kit should ensure worktops stay in good condition
Installation is relatively easy, for either a competent DIY enthusiast or recognised kitchen installer to carry out
No specialist tool required. Can be cut using normal woodworking routers and blades
Plan the worktop layout to ensure jonits don’t fall or within 100 mm of cut-outs

Complementary products and accessories
Corporate Office: Häfele America Co., 3901 Cheyenne Drive, Archdale, N.C. 27263
Phone: 800.423.3531, Fax: 800.325.6197, Local Phone: 336.434.2322, Email: info@haefeleamericas.com
28-Jun-2022