Individual Parts, for Aximat 100, 180°, Twin Mounting Exposed Axle Hinge

  • Features
    • LGA tested project quality in compliance with DIN EN 15570 test level 3 (80,000 cycles)
    • Large opening angle from 180° to 270° provided by external pivot point (axle)
    • Almost no loss of space inside the cabinet due to the flat design
    • Door installation with slide on (Aximat 100 A) or time-saving quick fixing system (Aximat 100 SM)
    • Cup for screw fixing or press fitting, hinge arm fixing into 32 mm series drilled holes
    • 2 or 3-dimensional adjustment facility for optimum alignment of the gap pattern
    • Cabinet construction or continuous construction possible
    • With integrated spring
    • Optional accessories available, e.g. opening angle restraint
    • Also available in RAL colours on request
    Tested quality
     
     
     
     
     
     
    Flat designExternal axleAlso available in special colours
    Additional accessories available (e.g. opening angle restraint, cover plates)
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
    Number of concealed hinges per door

    The values in the diagram are sample measurements for doors up to 600 mm wide. Please inquire for doors wider than 600 mm.

    With doors under 400 mm wide the minimum gap must be determined by trial mounting.

    The door’s width should not exceed its height.

    The distance between hinges of doors with two hinges must be at least as long as the door is wide, if possible even longer.

    In case of heavy loads and high leverage force, an additional hinge mounted approx. 100 mm (dim. X) below the top hinge is recommended.

  • Installation dimensions and drilling patterns

    Aximat 100 SM

    Drilling pattern for cup fixing

    For screw fixing

    Drilling pattern for hinge arm fixing

    x = 59 (66) with drilling pattern 45/9.5 (52/9)Drilling pattern 45/9.5Drilling pattern 52/9Full overlay mountingInset mounting
    For press fitting
    Drilling pattern 45/9.5Drilling pattern 52/9

    Aximat 100 A

    Drilling pattern for cup fixing

    Drilling pattern for hinge arm fixing

    For screw fixingFor screw fixing with chipboard screws
    y = 62 (66) with drilling pattern 48/6 and 45/9.5 (52/5.5)Drilling pattern 48/6
    For press fittingFor screw fixing with Euro screws
    Drilling pattern 48/6
     
     
     
     
     

    Drilling pattern 45/9.5

    For press fitting with pre-mounted spreading dowels
    Drilling pattern 52/5.5
    Note

    Dowel holes must be chamfered with HPL coated boards in order to avoid damaging the dowels during press fitting.

  • Montage und Demontage der Tür

    Aximat 100 SM (Schnellmontage-Technik)

    Montage

    Topf auf den Gelenkarm schieben, bis er einrastet

    Sicherheitseinrichtung verriegeln, Abdeckkappe vom Topf schließen

    Demontage

    Sicherheitseinrichtungentriegeln

    Abdeckkappe öffnen undTopf vom Gelenkarm abziehen

     

    Aximat 100 A (Aufschiebe-Technik)

    Montage

    Topf auf den Gelenkarm schieben

    Schrauben festziehen

    Demontage

    Schraube lösen

    Topf vom Gelenkarm abziehen

     

    Einstellmöglichkeiten

    Über die 2- bzw. 3-dimensionalen Einstellmöglichkeiten können Verarbeitungs- und Montageabweichungen korrigiert werden.

    Seiten-, Höhen- und Tiefeneinstellungen sind ab Werk in der Nullposition eingestellt.

    A Seiteneinstellung

    B Höheneinstellung

    C Tiefeneinstellung

    Aximat 100 SM mit 3-dimensionaler Einstellmöglichkeit

    A –3 mm über Exzenter

    B ±2 mm über Exzenter

    C ±2,5 mm über Langlöcher

     

    Aximat 100 SM mit 2-dimensionaler Einstellmöglichkeit

    A –3 mm über Exzenter

    B ±2 mm über Langlöcher

    Aximat 100 SM FS mit 2-dimensionaler Einstellmöglichkeit

    A 2 mm über Exzenter

    B ± 2 mm über Exzenter

    Aximat 100 A mit 2-dimensionaler Einstellmöglichkeit

    A –3 mm über Langloch

    B ±2 mm über Langlöcher

     
  • Door width calculation

     

    Key

    LSB = internal cabinet width

    TA = door overlay

    TB = door width

    F = gap

    Cabinet with 1 door

    External cabinet width

    400 mm

    Side panel thickness 2 x 19 mm

    38 mm

    Internal cabinet width

    362 mm

    LSB + (2 x TA)

    =

    Door width

    Example

    362 mm + (2 x 16 mm)

    =

    392 mm

     
     
     
     
     
     
     
     

    Cabinet with double doors

    External cabinet width

    800 mm

    Side panel thickness 2 x 19 mm

    38 mm

    Internal cabinet width

    762 mm

    LSB + (2 x TA) – (1 x F)

    =

    Door width

    2

    Example

    762 mm + (2 x 16 mm) – (1 x 6 mm)

    =

    394 mm

    2

     
     
     
     
     
     
     
     

    Continuous construction with double doors

    External cabinet width

    800 mm

    Side panel thickness 1 x 19 mm

    19 mm

    Internal cabinet width

    781 mm

    LSB + (2 x TA) – (1 x F)

    =

    Door width

    2

    Example

    781 mm + (2 x 6.5 mm) – (1 x 6 mm)

    =

    394 mm

    2

     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     

    Important processing note on hinge arm fixing

     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     

    * A third screw must be used for securing the hinge arm.

    Help

    Help

    Requested amount is in stock.
    Limited stock available.
    Item no longer available

    Note:
    To receive items as fast as possible, choose 'when available' at checkout.

    Don't know your article number? Select product features below
    See Required Products
    Product details
    • Two separate parts make item 344.21.013
    Product Features

    Order reference

    Order Hospa Ø 3.5 mm raised head screws separately for Hospa screw fixing versions

    27-May-2019

    Individual Parts, for Aximat 100, 180°, Twin Mounting Exposed Axle Hinge

    6 mm gap

    Image may show a similar article, please check product details.

    Note

    Please select an article via the features or article table in order to add it to the basket.